General Purpose
Sizes 1/8″ through 3″ have forged bases.
Entire Clip – Hot Dip galvanized to resist corrosive and rusting action.
Only Genuine Crosby Clips have a Red U-BOLT for instant recognition.
All Clips are individually bagged or tagged with proper application instructions and warning Learn More
G-209 Screw Pin
Anchor Shackles
G-209 Screw pin anchor shackles meet the performance requirements of Federal Specification RR-C-271F Type IVA, Grade A, Class 2, except for those provisions required of the contractor.
Forged Steel—Quenched and Tempered.
Recommended for straight line pull.
Working Load Limits shown are for In-line pull.
Fatigue rated at 1 1/2 times the Working Load Limit at 20,000 cycles.
Ultimate Load is 5 times the Working Load Limit
Learn More
Forged Steel—Quenched and Tempered. Hot Dip galvanized.Learn More
Wedge sockets meet the performance
requirements of Federal Specification
RR-S-550E, Type C, except those provisions
required of the contractor.
Learn More
Forged Carbon Steel or Forged Alloy Steel — Quenched and Tempered. Not Suitable for use with Grade 80 chain and chain slings used in overhead lifting. For slings or lifting chains, Grade 80 or 100 alloy components are recommended. for Crosby Spectrum 7® chain
Learn More
Forged Steel.
Hot Dip galvanized.
Furnished with standard Hot Dip galvanized, heavy hex nuts.
Ulitmate Load is 5 times the Working Load Limit
Learn More
Hot Dip galvanized steel.
End fittings are Quenched and Tempered, bodies heat treated by normalizing.
Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckle sizes 1/4″ through 21/2″, a shackle one size Learn More
Hot Dip galvanized steel.
End fittings are Quenched and Tempered, bodies heat treated by normalizing.
TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
Forged jaw ends are fitted with bolts and nuts for 1/4″ through 5/8″, and pins and cotters on
Learn More
Forged Carbon Steel or Forged Alloy Steel — Quenched and Tempered.
All Pins Alloy Steel — Quenched and Tempered.
Not Suitable for use with Grade 80 chain and chain slings used in overhead lifting. For slings or lifting chains, Grade 80 or 100 alloy components are recommended.
Learn More
Forged Steel – Quenched and Tempered
Design factor is 4:1
Features quick and easy assembly
H-330 designed for Crosby Spectrum 4® chain
A-330 designed for Crosby Spectrum 7® chainLearn More
The Crosby “Synthetic Sling Saver” Shackle, designed for Round or Flat Synthetic Slings, has the following features:
- Eliminates “bunching” effect caused by traditional shackles.
- Reduces sling tendency to slide.
- Quenched and Tempered.
- Alloy bows, Alloy bolts.
- Forged Alloy Steel 30 thru 175 metric tons. Cast Alloy Steel 200 thru 400 metric tons.
Forged Alloy Steel, Quenched & Tempered
Deep straight throat permits efficient handling of flat plates or large cylindrical shapes.
The long tapered point allows easy grab in rings, pear links, eye bolts or lifting holes.
Forged Steel, Quenched & Tempered
- Pressed steel latches and stainless steel springs, bolts and nuts.
- Safe Working Loads shown are based on Ultimate Load that is 4 times the Safe Working Load.
Sliding Choker Hooks
Quenched & Tempered
FORGED ALLOY STEEL through 3/4″.
Wide throat to take heavy thimbles.
Ultimate Load is 5 times Safe Working Load
- The most complete line of eye hoist hooks. Available 3/4 to 60 tons.
- Proper design, careful forging and precision controlled quench and tempering give maximum strength without excessive weight and bulk.
The Web Sling hook, originally designed for 2-Ply Web slings, can also be used with Round Slings as long as the Working Load Limit ratings are compatible. The new hook incorporates the following features:
- Alloy Steel — Quenched and Tempered.
- Individually Proof Tested to values shown, with certification.
- Proof Tested with 60% inside width special fixtures sized to prevent localized
point loading per ASME A-952 , reference page 276.
-
- Forged from special bar quality carbon steel, suitable for cold forming.
- Swage Socket terminations have an efficiency rating of 100% based on the
catalog strength of wire rope.
- Hardness controlled by spheroidize annealing.
Close Swage Sockets
-
- Forged from special bar quality carbon steel, suitable for cold forming.
- Swage Socket terminations have an efficiency rating of 100% based on the
catalog strength of wire rope.
- Hardness controlled by spheroidize annealing.